BLUE JOTTER

  • Subscribe to our RSS feed.
  • Twitter
  • StumbleUpon
  • Reddit
  • Facebook
  • Digg

Monday, 31 May 2010

Making a rudder, part 4: designing gudgeons

Posted on 09:37 by Unknown
With my rudder blade is almost ready for the water, so time to think about it can connect to the boat. To hang it from Briongloid's stern, I need to make a pair of gudgeons; these will allow it to pivot about a vertical axis, and need enough strength to prevent it either from being swept astern or from bobbing up out of the water (the Corecell interior being much less dense than water, the finished rudder is going to be quite buoyant, even with much of the length out of above the surface). Also, we are now talking about a moving part, and so friction is a problem: the gudgeon needs to pivot about a stainless steel pin without appreciable wear to either itself or the pin. Two separate mechanical challenges for our gudgeons: what materials should we use?

Figure 1: Gudgeons (yellow) allow a transom-hung rudder (blue) to pivot about a vertical axis (red)

To give the parts the necessary strength (tensile strength being what they need most), I have decided to imitate the gudgeons that held the old rudder, which were made in stainless steel and worked fairly well. However, I can't work in stainless steel (no skills, no tools, no materials), so I chose a different material, more impervious to corrosion and with even more impressive tensile strength: carbon fibre (weight for weight, the median sample of carbon fibre has six times the tensile strength of stainless steel [Source: Wolfram Alpha]. This can be bought as a woven fabric, just like fibreglass, and worked with the same simple tools - epoxy resin, a pair of scissors, etc (Kevlar needs special shears, but ordinary scissors will do for "mere" carbon fibre). Strength problem: solved.

So much for strength: what about friction? This is a moving part, a type of bearing, and Mr. Friction is not our friend. The pivoting action of the gudgeon around the steel pin is going to cause wear if I just use epoxy-impregnated carbon fibre. For the core of the bearing, a different material is required - strong, but also slippy. After some research, I found the solution on the excellent blog of a Canadian who is building "Raven", a nippy trimaran from Ian Farrier's F22 design. This gentleman used a plastic PET-P, Polyethlyene Terypthalate, also sold as Ertalye, in just the same situation. This particular wonder material shrugs off water, is nice and slippy, and and also pretty strong. With a little research, the amateur builder can buy small quantities in rod or sheet form. Just the thing for the core of our bearing.

Figure 2: Gudgeon cores (carbon fibre ties not pictures)

Figure 2 above illustrates the core of the gudgeons, with the long base of the triangle being mounted on the leading edge of the rudder itself. Layers of carbon fibre cloth around the outside bind the core to the rudder in a continuous loop for maximum strength. The hardwood insert is there just to save some epoxy (cut from the ruined old rudder, it saves me a few pence worth of epoxy and provides similar strength). The hole in the centre of the PET-P cylinder is where the pintle goes, so the gudgeon can fulfil its pivoting function.

Coming in the next post: making and mounting the gudgeons

Previous posts in the series:
Designing a rudder, part 1
Designing a rudder, part 2
Making a rudder, part 1
Making a rudder, part 2
Making a rudder, part 3


Read More
Posted in carbon fibre, ertalyte, gudgeons, pet-p | No comments

Sunday, 11 April 2010

Taking the long way around

Posted on 13:11 by Unknown
In which no rudders are mended, but some beautiful footage is watched.

As the weather finally warms enough for epoxy to set and my boat repairs to continue, I'm looking forward more and more eagerly to (re)launch day. Until then, perhaps the next best thing is to watch a man called Dylan Winters circumnavigating Britain, very slowly in "the slug", a Mirror Offshore (19 feet, with inboard diesel, designed by Van de Stadt, the same man who designed my own poor Briongloid).

What makes an already-ambitious trip even longer and more impressive is that Mr. Winters is not taking the shortest route. Instead, he sails as far as possible up every river of interest along the way - from giants like the Thames, to tiny backwaters like Beaumont Quay (up a canal dug by slaves in Roman times). Along the way, he takes beautiful HD footage of boats large and small - lately, gorgeous Thames barges have been a recurring them.

A professional film-maker and seasoned editor, his films come with illuminating commentary on the history of the places he visits, and his lovely shots of sea and river are complemented by lovely soundtrack by the likes of Cities of Foam.

Enough talking; if you take even a passing interest in things boaty or the British coastline, do yourself a favour and wander over to Keep Turning Left. Well worth the price of admission.


Read More
Posted in | No comments

Saturday, 10 October 2009

Making a new rudder, part 3

Posted on 15:05 by Unknown
Designing a rudder, part 1
Designing a rudder, part 2
Making a rudder, part 1
Making a rudder, part 2

After lots of careful shaping of details (mostly with an orbital sander) and filling in the odd accidental gouge (using a mixture of epoxy and colloidal silica - which sets into a very tough and water-impervious substance), I was nearly ready to laminate.

From Laminating new rudder
Hardwood inserts epoxied in place, ready to take bolts

The final pre-lamination step was to drill big holes where the bolts connecting rudder to yacht will later sit, out to a radius of 5 times the bolt size: since Corecell is too soft to hold stainless steel bolts, I fixed hardwood inserts (chiseled from the remains of my old rudder) in place with lots of epoxy/colloidal silica mix to fill the gaps (actually, the wood was not technically necessary - but cheaper than epoxy, and a nice link with the old rudder, so in it went). Now, my rudder is a wood/corecell/epoxy/colloidal silica composite - and we've not even started with the glass fibre yet.


From Laminating new rudder
Rudder core, fully shaped, smoothed, faired, and ready for lay-up

Next step was to cut glass cloth to size; this is beautiful stuff - layers of four-harness satin alternating with heavy unidirectional fabric. It isn't that easy to cut, especially the 500g/metre stuff - glass is really hard. Also, the material looks almost too beautiful to use.


From Laminating new rudder
Unidirectional glass fabric, 500g/square metre

Before laminating, I need to don my protective gear - epoxy is great stuff, but not for the human body. I always wear eye protection in case of silly accidents, nitrile gloves (I'm now using cheap disposables instead of the heavy duty items pictured - latex won't do, by the way), rubber boots (because there are always drips and spatters), overalls (well, duh!) and an apron (because I tend to lean against the workbench, and my overalls nearly soaked through once).


From Laminating new rudder
Ready for Fun with Chemicals

From Laminating new rudder
Wet fabric (transparent) draped over the rudder core

My first couple of layups went pretty well - except I laid the epoxy on way too thick; extra does not add extra strength, only weight - and it is pricey stuff to be wasting. In the picture above, note the puddles of excess epoxy sitting on top of the cloth, and the messy ends at the rudder head (beside the squeegee) that I had to grind off after the resin had set. Hard to see, but important: the plywood workbench has been covered in white-faces hardboard (cheap enough to bin later) which in turn has been covered with a transparent polyethelene sheet (does not stick to epoxy).

Miscellaneous tips:
  • Clean your squeegee straight after use, while the resin is still soft
  • Buy a set of cheap brushes from Tesco for dabbing on resin wherever dry spots show up (€1.25 gets you 3 brushes in our local). Ditch after use (too hard to clean).
  • Disposable nitrile gloves give great tactile feedback - actually better than the heavy kind (plus, no clean-up). Very, very cheap at B&Q - and insanely cheap on E-bay.
  • It is much easier to use too much resin than too little
  • ...but you still need to keep an eagle eye for dry spots.
  • take your time and do careful work - resin sets fast, but not crazy fast
  • use peel ply - leaves a lovely smooth easy-to-work with surface, helps remove excess resin, well worth the money
  • an ounce of preparation (masking tape, polyethylene sheets, etc.) saves a ton of fixing up later

Read More
Posted in | No comments

Thursday, 8 October 2009

Toys

Posted on 14:16 by Unknown
Our son has reached The Age of Exploration. At last, he can pull himself upright and toddle along on his hind paws - so long as a support of some kind remains within reach. To give him some walking practice and a little independence, I sketched out a pushing/walking toy, then started digging through our wood-pile. Soon, odds and ends had been sawed and screwed into something closely resembling the sketch below (the height for the bars chosen to be just around our son's shoulders, low enough to be pushable, too high to fall over). One point to note: sanding off all edges and any rough surfaces will save grief later. With even a very cheap random orbital sander, this does not take long.


Version 1: Sled with upright handle

Full of anticipating, I presented the result of my labours to my son, who got the idea of the toy straight away, and set off at high speed, cackling with glee... and seconds later, rammed it a cupboard dead-on. No damage done, but also, no possibility of turning. The next problem was that he stood inside the sled, and tried to pull it over his own toes.


Version 2: platform to stand on, double-ended

I decided to solve the turning/reversing problem by making the pusher double-ended, duplicating the existing upright handle, and solved the standing-in-the-middle problem with a plywood platform. As I finished screwing this on, it occurred to me that I should have used bolts to secure the uprights to the base - then it would be very easy to take the whole thing apart into flat pieces for storage or transport.

The modifications were well received by my tiny test pilot: he used an upright to pull himself to his feet, then clambered grinning onto the platform, and tugged mightily at a handle, doing his best to rock the whole contraption. Which gave Dad an idea.


Version 3: build-in rocking function!

The final (so far) modification required some fairy delicate wood shaping: I made a long shallow curve from a single piece of wood, sawing, chiseling, sanding, then split it lengthwise into two identical pieces, which I glued with ordinary wood glue (do not risk snagging a screw head on your partner's tiles/carpet!) carefully to the existing runners, then clamped and allowed to set overnight.

Next morning, a very proud Dad presented his soon with the push-me-pull-you version. Son discovered that the new version made a very pleasing racket as it rocked on the kitchen tiles, and Dad was relieved to find that he hadn't overdone the rocking motion (no danger of head-over-heels).

This has been my first real foray into toy-making, at least as an adult; my son has got a lot of fun and exercise from a very simple toy, and I just as much, from the pleasure of making, of giving, and of seeing his fun.

Dads, Mums, Aunties and Uncles: to your sheds! Go build!

Read More
Posted in babies, carpentry, toddlers, toys, woodwork | No comments

Sunday, 20 September 2009

Making a new rudder, part 2

Posted on 13:40 by Unknown
This post is part of a series on making a fibreglass rudder with a foam core:
Designing a rudder, part 1
Designing a rudder, part 2
Making a rudder, part 1

Calculations done, foam cut into neat rudder-sized rectangles, I had no alternative but to start shaping the foam. I did it like this...

Step 1: mark the depth of foam to be removed. I did this by setting a circular saw to the calculated depth for a given point in the profile, then running it the length of the rudder. I kept the trenches very close together at the leading edge of the foil - the first few tracks were only 2mm apart (the saw blade width), then, as the slope of the foil changed more slowly 4mm, 5mm, 10mm. On the rear half of the foil, whose slope is almost straight, the gaps increased to 20mm, then 40mm. With all the tracks cut, I sprayed blue paint into the cuts, making sure to get good coverage on the bottoms of the tracks.

Step 2: remove the bulk of the foam. I tried chisels: bad idea. What worked really well was to take a wood saw, hold it sideways and cut along the foil at a shallow angle, keeping a millimetre or two above the bottom of the trenches. In about 40 minutes I was able to remove most of the excess foam, leaving behind a nice flat surface.

Saws make short work of Corecell

Step 3: the saw was followed by a wood plane, which cut to within 1-0.5mm of the trench bottoms - but not lower, because the plane did not cut the foam as smoothly as wood, tending to leave the surface a little rough.

Step 4: I next used a surform to remove the last of the excess foam, leaving the surface of the foil flush with the trench bottoms.

Step 5: To get a really smooth finish, I followed up the surform with a random orbital sander.


With the two halves shaped and (I hoped) pretty symmetrical, I mixed up 250mm of epoxy, then stirred in enough colloidal silica (amazingly fine white powder) to make a paste with a honey-like consistency. A squeegee was perfect for getting an even spread on the flat side of the starboard foil half. Interesting to note: although the foam looks like a sponge, it certainly doesn't act like it - it doesn't the epoxy in, but leaves it on the surface - where I need it .


Rudder core halves clamped together; polythene drapes keep epoxy off the worktop

With an even spread of epoxy covering the starboard half, I dropped the port half into position, and applied my entire collection of clamps. You never have enough clamps. And that was it for the day: all going well, by tomorrow morning, the two halves will be one - permanently.
Read More
Posted in corecell, rudder | No comments

Friday, 18 September 2009

Long Ears

Posted on 15:51 by Unknown
In the morning, there was a small brown scrap on our lawn where none had been before. Turning over, as I thought, the corpse of a headless bat, I was startled by squeaks of fear or rage. The mouse-sized animal had curled its wings in tight around its body, and tucked its head into its chest; even its ears had curled up, looking something like a ram's horns. The face was relatively pretty, as bats go, without the weird pressed-up nose that some species have; the massive ears are the feature you'll remember, though.

Brown long-eared bat


According to the excellent "Exploring Irish Mammals", Plecotus auritus, described by Linaeus in 1758, is found across most of Europe north of the Pyreness, and also in the far east, in regions within Russia, China, and Japan. This bat likes to "foliage glean", plucking its prey from leaves or even the ground as it flys.

~

My tiny specimen was soaked in dew, and motionless - this last must be what saved it from our cat, who loves to chase, but tires of prey which can no longer flee. I tucked my patient away for the day in an empty toolbox, with a few crumbs of cat food for sustenance.

~

After sunset, I took my patient for a walk, to a wooded and cat-free place. Out of the toolbox, the ears inflated and the head looked up; then, the tiny creatures crawled from my gloved hand onto the rough bark of a large tree, hooking on tight with claws on the leading edge of the wing, while black and hand-like hind paws sought purchase.
Read More
Posted in bats, linnaeus | No comments

Tuesday, 25 August 2009

Making a new rudder, part 1

Posted on 09:33 by Unknown
Following on from the previous posts on the design of rudder foils, our hero now begins the tricky fabrication stage.

As discussed previously, my new rudder will have a fibreglass skin (6 layers) wrapped around a foam core. Not just any old foam - Corecell, a light, stiff material that is absorbs little resin (or water) and will contain any damage to a very localised area. It won't rot, delaminate or crack, and the sheet I bought from the helpful folk at MID has a density of just 60kg / cubic metre.

I've never used this material before, so wasn't sure how easy it would be to work with. First, I trimmed the lengths I needed for the rudder itself from the original 4ft by 8ft x 25mm sheet using a jig saw. No problems, and surprisingly little dust - most of the material from the kerf seemed to stick together, hinting at one potential difficultly: since this foam is a very good insulator, heat from cutting tools disspates slowly - so cutting at higher speeds can cause melting.

Next, I used an off-cut to practice my foam-shaping skills (never shaped foam before, didn't want to start by destroying my proto-rudder). First, I clamped a straight-edged piece of wood atop the foam as a cutting guide (straightness verified against a handy glass window - float glass is very flat). Then, I set the cutting depth on my hand-held circular saw and cut a series of trenches in the foam, the depths calculated from my spreadsheet describing the NACA 0012 foil I want to make.


Next, I sprayed the yellow foam with blue paint, making certain it penetrated to the bottom of the trenches.
Once the blue paint was on, it was now "safe" to start cutting away excess foam; I tried a random orbital sander, but, especially at high revs, discs clogged too quickly. Tried a sharp penknife: not too useful. A block plane worked reasonably well, and a rasp/file came in very handy for tidying up small irregularities. The paint worked a treat - you can see below how the blue lines allow me to be sure I've not removed too much material.


Shaping the leading edge of the foil was quite easy; shaping the trailing edge - much more material to remove, but accuracy is less crucial - turned out to be more difficult. I actually tried chiseling, which worked up to a point, but was slow and difficult. Not sure about the best way to do this yet - I hope to try an angle grinder soon to slice the bulk off, then follow that with plane, disc sander and rasp for the final finish.

Conclusions so far: Corecell is very easy to cut. Shaping it is much easier than shaping wood, but the same techniques won't work.

This post is part of a series on making a fibreglass rudder with a foam core:
Designing a rudder, part 1
Designing a rudder, part 2
Making a rudder, part 1
Read More
Posted in | No comments
Newer Posts Older Posts Home
Subscribe to: Posts (Atom)

Popular Posts

  • CPU Hog
    So there I was, tapping away at quotidian tasks, when I noticed my PC was responding with all the dash and verve of a fossilized member of T...
  • Making a new rudder, part 3
    Designing a rudder, part 1 Designing a rudder, part 2 Making a rudder, part 1 Making a rudder, part 2 After lots of careful shaping of detai...
  • Designing a new rudder, part 2
    By measuring photographs and doing a little maths, courtesy of the NACA 0012 formula, I was able to discover what size and shape my new rudd...
  • Saving up for a... sunny day?
    You may have heard the advice that you should have cash on hand to cover living expenses for some few months, just in case - "rainy day...
  • Making a new rudder, part 1
    Following on from the previous posts on the design of rudder foils, our hero now begins the tricky fabrication stage. As discussed previou...
  • Installing DELL laptop drivers from CABs
    Recently, I had to rebuild my Dell laptop.  Not fun.  Hoping to save someone else a little time, here is how I got all the drivers sorted: F...
  • Making a new rudder, part 2
    This post is part of a series on making a fibreglass rudder with a foam core: Designing a rudder, part 1 Designing a rudder, part 2 Making a...
  • Cleaning a microwave oven
    The levels of dried-out burnt-on food on the roof of our microwave oven were well below bachelor-tolerance levels, and, considering the dose...
  • Error Propagation: an unexpected beauty
    So, say you have a couple of measurements, x and y, with some associated uncertainty; the true value of x might be, say, 3 units above or be...
  • Review: Imray Chart Plotter (ID30)
    In the current economic climate, the demand for my services has decreased; so, less cash. Luckily, this also means more time for sailing. ...

Categories

  • 3d printing
  • adapter
  • aerofoil
  • Android
  • app
  • apps
  • arcturus
  • astronavigation
  • babies
  • bats
  • battery
  • boat
  • cam
  • camcorder
  • carbon fibre
  • carpentry
  • celestial navigation
  • certainty
  • charts
  • chemistry
  • clean
  • composite
  • computer vision
  • corecell
  • CPU
  • debugging
  • dementia
  • digital charts
  • error
  • error propagation
  • ertalyte
  • fibreglass
  • financial independence
  • foil
  • formula
  • frugality
  • geometry
  • Google Desktop
  • grp
  • gudgeons
  • how to
  • ideas
  • imray
  • installing linux
  • interesting
  • investment
  • latitude
  • linnaeus
  • linux
  • lock screen
  • longitude
  • maths
  • microwave
  • moon
  • navigation
  • operating system
  • oven
  • pc
  • pet-p
  • probability
  • Process
  • programming
  • puppy linux
  • pythagoras
  • rapid prototyping
  • repair
  • retirement
  • review
  • rudder
  • Samsung Galaxy
  • savings
  • shapeways
  • Speed Launcher
  • statistics
  • sugru
  • toddlers
  • toys
  • wander alarm
  • wide-angle
  • windows
  • wood
  • woodwork
  • yacht

Blog Archive

  • ▼  2012 (3)
    • ▼  October (1)
      • Installing DELL laptop drivers from CABs
    • ►  July (1)
    • ►  February (1)
  • ►  2011 (2)
    • ►  December (1)
    • ►  August (1)
  • ►  2010 (6)
    • ►  October (1)
    • ►  August (1)
    • ►  July (2)
    • ►  May (1)
    • ►  April (1)
  • ►  2009 (13)
    • ►  October (2)
    • ►  September (2)
    • ►  August (1)
    • ►  July (1)
    • ►  June (4)
    • ►  April (1)
    • ►  February (1)
    • ►  January (1)
  • ►  2008 (9)
    • ►  December (2)
    • ►  November (7)
Powered by Blogger.

About Me

Unknown
View my complete profile