BLUE JOTTER

  • Subscribe to our RSS feed.
  • Twitter
  • StumbleUpon
  • Reddit
  • Facebook
  • Digg

Tuesday, 25 August 2009

Making a new rudder, part 1

Posted on 09:33 by Unknown
Following on from the previous posts on the design of rudder foils, our hero now begins the tricky fabrication stage.

As discussed previously, my new rudder will have a fibreglass skin (6 layers) wrapped around a foam core. Not just any old foam - Corecell, a light, stiff material that is absorbs little resin (or water) and will contain any damage to a very localised area. It won't rot, delaminate or crack, and the sheet I bought from the helpful folk at MID has a density of just 60kg / cubic metre.

I've never used this material before, so wasn't sure how easy it would be to work with. First, I trimmed the lengths I needed for the rudder itself from the original 4ft by 8ft x 25mm sheet using a jig saw. No problems, and surprisingly little dust - most of the material from the kerf seemed to stick together, hinting at one potential difficultly: since this foam is a very good insulator, heat from cutting tools disspates slowly - so cutting at higher speeds can cause melting.

Next, I used an off-cut to practice my foam-shaping skills (never shaped foam before, didn't want to start by destroying my proto-rudder). First, I clamped a straight-edged piece of wood atop the foam as a cutting guide (straightness verified against a handy glass window - float glass is very flat). Then, I set the cutting depth on my hand-held circular saw and cut a series of trenches in the foam, the depths calculated from my spreadsheet describing the NACA 0012 foil I want to make.


Next, I sprayed the yellow foam with blue paint, making certain it penetrated to the bottom of the trenches.
Once the blue paint was on, it was now "safe" to start cutting away excess foam; I tried a random orbital sander, but, especially at high revs, discs clogged too quickly. Tried a sharp penknife: not too useful. A block plane worked reasonably well, and a rasp/file came in very handy for tidying up small irregularities. The paint worked a treat - you can see below how the blue lines allow me to be sure I've not removed too much material.


Shaping the leading edge of the foil was quite easy; shaping the trailing edge - much more material to remove, but accuracy is less crucial - turned out to be more difficult. I actually tried chiseling, which worked up to a point, but was slow and difficult. Not sure about the best way to do this yet - I hope to try an angle grinder soon to slice the bulk off, then follow that with plane, disc sander and rasp for the final finish.

Conclusions so far: Corecell is very easy to cut. Shaping it is much easier than shaping wood, but the same techniques won't work.

This post is part of a series on making a fibreglass rudder with a foam core:
Designing a rudder, part 1
Designing a rudder, part 2
Making a rudder, part 1
Read More
Posted in | No comments
Newer Posts Older Posts Home
Subscribe to: Posts (Atom)

Popular Posts

  • CPU Hog
    So there I was, tapping away at quotidian tasks, when I noticed my PC was responding with all the dash and verve of a fossilized member of T...
  • Making a new rudder, part 3
    Designing a rudder, part 1 Designing a rudder, part 2 Making a rudder, part 1 Making a rudder, part 2 After lots of careful shaping of detai...
  • Designing a new rudder, part 2
    By measuring photographs and doing a little maths, courtesy of the NACA 0012 formula, I was able to discover what size and shape my new rudd...
  • Saving up for a... sunny day?
    You may have heard the advice that you should have cash on hand to cover living expenses for some few months, just in case - "rainy day...
  • Making a new rudder, part 1
    Following on from the previous posts on the design of rudder foils, our hero now begins the tricky fabrication stage. As discussed previou...
  • Installing DELL laptop drivers from CABs
    Recently, I had to rebuild my Dell laptop.  Not fun.  Hoping to save someone else a little time, here is how I got all the drivers sorted: F...
  • Making a new rudder, part 2
    This post is part of a series on making a fibreglass rudder with a foam core: Designing a rudder, part 1 Designing a rudder, part 2 Making a...
  • Cleaning a microwave oven
    The levels of dried-out burnt-on food on the roof of our microwave oven were well below bachelor-tolerance levels, and, considering the dose...
  • Error Propagation: an unexpected beauty
    So, say you have a couple of measurements, x and y, with some associated uncertainty; the true value of x might be, say, 3 units above or be...
  • Review: Imray Chart Plotter (ID30)
    In the current economic climate, the demand for my services has decreased; so, less cash. Luckily, this also means more time for sailing. ...

Categories

  • 3d printing
  • adapter
  • aerofoil
  • Android
  • app
  • apps
  • arcturus
  • astronavigation
  • babies
  • bats
  • battery
  • boat
  • cam
  • camcorder
  • carbon fibre
  • carpentry
  • celestial navigation
  • certainty
  • charts
  • chemistry
  • clean
  • composite
  • computer vision
  • corecell
  • CPU
  • debugging
  • dementia
  • digital charts
  • error
  • error propagation
  • ertalyte
  • fibreglass
  • financial independence
  • foil
  • formula
  • frugality
  • geometry
  • Google Desktop
  • grp
  • gudgeons
  • how to
  • ideas
  • imray
  • installing linux
  • interesting
  • investment
  • latitude
  • linnaeus
  • linux
  • lock screen
  • longitude
  • maths
  • microwave
  • moon
  • navigation
  • operating system
  • oven
  • pc
  • pet-p
  • probability
  • Process
  • programming
  • puppy linux
  • pythagoras
  • rapid prototyping
  • repair
  • retirement
  • review
  • rudder
  • Samsung Galaxy
  • savings
  • shapeways
  • Speed Launcher
  • statistics
  • sugru
  • toddlers
  • toys
  • wander alarm
  • wide-angle
  • windows
  • wood
  • woodwork
  • yacht

Blog Archive

  • ►  2012 (3)
    • ►  October (1)
    • ►  July (1)
    • ►  February (1)
  • ►  2011 (2)
    • ►  December (1)
    • ►  August (1)
  • ►  2010 (6)
    • ►  October (1)
    • ►  August (1)
    • ►  July (2)
    • ►  May (1)
    • ►  April (1)
  • ▼  2009 (13)
    • ►  October (2)
    • ►  September (2)
    • ▼  August (1)
      • Making a new rudder, part 1
    • ►  July (1)
    • ►  June (4)
    • ►  April (1)
    • ►  February (1)
    • ►  January (1)
  • ►  2008 (9)
    • ►  December (2)
    • ►  November (7)
Powered by Blogger.

About Me

Unknown
View my complete profile